Agricultural systems engineering (greenhouse, fish farming, mushroom production)
H. Faridi; A. Arabhosseini; Gh. Zarei; M. Okos
Abstract
In this research, an attempt was made to utilize an Earth-Air Heat Exchanger (EAHE) system as a source of shallow geothermal energy to provide thermal demands of a commercial greenhouse located in Alborz province, Iran. The degree-day index was applied to estimate the EAHE system’s potential to ...
Read More
In this research, an attempt was made to utilize an Earth-Air Heat Exchanger (EAHE) system as a source of shallow geothermal energy to provide thermal demands of a commercial greenhouse located in Alborz province, Iran. The degree-day index was applied to estimate the EAHE system’s potential to meet the thermal requirements of the greenhouse including cooling and heating demands. The results indicated that this region needed more energy to reach to the relevant temperature inside the greenhouse for the heating demand comparing to the cooling one. The average potential of the EAHE system based on the degree-day index was 10.76ºC for increasing temperature in the cold and 17.96ºC for decreasing temperature in the warm season. This means that the EAHE system was capable of supplying the greenhouse thermal demands in this area according to the calculated values of Heating Degree-Day (HDD) and Cooling Degree-Day (CDD). This method would be beneficial in monitoring and optimizing plant growth conditions as the best crop type or cultivation selection which in turn can help in irrigation and fertigation management of the crop grown.
H. Samimi Akhijahani; A. Arabhosseini; M. H. Kianmehr
Abstract
Introduction
Drying is one of the most common methods for storing food and agricultural products. During drying process, free water that causes the growth of microorganisms and spoilage of products is removed from the product. There are several methods for drying of agricultural products. one of the ...
Read More
Introduction
Drying is one of the most common methods for storing food and agricultural products. During drying process, free water that causes the growth of microorganisms and spoilage of products is removed from the product. There are several methods for drying of agricultural products. one of the most important methods of investment is drying by using sunlight. Iran is situated at 25- 43oE longitude and mean solar radiation is about 4.9 kwh.m-2.d-1. Because of the proper solar radiations in 95% of the agricultural areas in Iran, solar drying is widely used for drying of fruits and vegetables. The use of solar dryer causes saving in energy consumption and processing costs for drying of products in farms and gardens. Several researchers investigated heat transfer and heat flow in dryers. Selection of appropriate method was carried out for drying of agricultural products using heat pump. Experiments were done and mathematical relationships were estimated to obtain correlation parameters between Reynolds number and Nusselt number for the three cases of solar dryer (cabinet, indirect and combination).The best working conditions were determined for three types of solar collectors (flat, finned and corrugated). In this study, the process of heat transfer and heat transfer coefficient of a solar dryer with and without rotation of absorber plate was compared.
Materials and Methods
The experiments were conducted in Azarshahr, East Azarbayjan province, Iran in September 2014. Newton's law of thermodynamic was used to analyze the working condition of solar absorber. For this purpose the absorber plate was divided into four equal parts. According to the thermal equations and related boundary conditions as well as the relationship between heat transfer coefficient and the temperature gradient, equation 1 for the Nusselet number obtained:
1
Beside the relationship between Nusselt number and heat transfer coefficient is defined as equation 2:
2
Finally variation of total heat flow over the time at different surfaces of the collector is determined by using equation 3:
3
Two cases (solar panel with rotation and without rotation) were considered for testing. Data measuring was carried out for 9 hours from 8 to 17. The fluid flow rate was 0.0185m3.s-1. The dryer was installed in an environment with air temperature of 31.6 oC and 31.8 oC, with the air velocity of 0.58 m.s-1 and 0.54 m.s-1 and with the relative air humidity of about 21%and 21.5% at the first and second days, respectively. The dryer had an automatic temperature controller to fix the air temperature with an accuracy of ±0.1 oC. An anemometer Yk-2005AM model was used to regulate the required air velocity. The output data of the thermocouples was recorded by a digital thermometer (DL-9601A, Lutron) that was connected to a computer using RS232 cable and recorded the temperature at required point every an hour. The relative humidity of the ambient was measured every hour with a digital hygrometer (HT.3600, Taiwan), accuracy of 3%. By assembling controlling system with a DC motor, a precious photocell and a proper mechanism, the frame would rotate by the sun and followed solar radiation, therefore more solar energy produced in solar panel.
Results and Discussion
The results of the experiments showed that the heat transfer process increased in both cases from the early morning and reached to its maximum value around 12 to 14 o’clock. The trend was more homogeneous in the dryer by absorber plate without rotation due to the decline of the heat accumulation. The mean temperature rise in the solar dryer without rotation was 37oC and in the solar dryer with rotation was 54oC. Because of the rotation of solar plate, variations of solar radiation were low. Therefore, by rotation of the solar dryer panel the temperature rise was 27oC. The values of heat transfer coefficient in the solar dryer with rotation were decreased by the time. This reduction in the hours before noon is more than after noon. This is due to the reduction of the temperature gradient in the solar absorber plate. Also the results showed that heat transfer coefficient in the lower levels (S1 and S2) is more than higher levels (S3 and S4). Variations of the heat flow for the solar dryer with rotation is more than the other. Because in the first one, the absorber plate was followed the solar radiation and generated heat in the plate increases and the fan does not have the ability to discharge the generated heat. The total amount of heat transfer in absorber plate with rotation was 36.1% higher than the absorber plate without rotation. To increase the heat transfer from the dryer, design of the system to change air flow rate by increasing temperature, can increase the efficiency of the dryer.
Conclusions
In this study the performance of the absorber plate in a solar dryer in two cases with rotation and without rotation were compared. The results showed that by rotation of the solar absorber plate the output temperature of the collector rises about 27oC. Thermal fluctuation in the rotation solar plate is lower than the solar plate without rotation.
H. Bagheri; A. Arabhosseini; M. H. Kianmehr
Abstract
In this research, solar drying of a thin layer of tomato slices was evaluated. The experiments were carried out at the air velocities of 0.5 and 1.0 m s-1 and thicknesses of 3, 5 and 7 mm. In order to find the most suitable form of thin layer drying model, nine different mathematical drying models were ...
Read More
In this research, solar drying of a thin layer of tomato slices was evaluated. The experiments were carried out at the air velocities of 0.5 and 1.0 m s-1 and thicknesses of 3, 5 and 7 mm. In order to find the most suitable form of thin layer drying model, nine different mathematical drying models were fitted to the experimental data to determine the pertinent coefficients of each model. The goodness of the fit was determined by calculating and comparing the values of the correlation coefficient (R^2 ) Root mean square error (RMSE) and chi-square (χ^2) for all models. The Page model with R^2=0.9974 ,χ^2=0.01351 , RMSE=0.002 showed the best fit.
